To create an instruction for automatic geometry assignment, add a row in the Geometry Assignments tab, and then make an entry in each column in the row. Each row creates one line in the APA file.
For example the following row assigns page geometry settings to the refined page named Cover.p1.pdf.
Refined file name | Offset X | Offset Y | Trim size X | Trim size Y | Scale X | Scale Y | Orientation |
---|---|---|---|---|---|---|---|
Cover.p1.pdf | -36 pt | -36 pt | 612.0 pt | 792.0 pt | 100% | 100% | 0 |
You can explicitly name the refined file or use wild cards.
Using geometry settings from the input file
You can assign geometry from one of two sources:
- From parameters set in the APA file
- From the page. To use this method, enter
Mixed
in the column for that parameter in the Geometry Assignments view, such as offsets, scaling, trim, or orientation.
Note: Some input files may not contain offsets. For example, DCS/EPS files will not contain offsets. PostScript files generated from a native software application using the Prinergy Refiner PPD will always contain offsets.
Unit of measure conversion
For Offset X, Offset Y, Trim Size X, Trim Size Y:
- On the Geometry Assignments tab, you can enter points, millimeters, centimeters, or inches. Valid unit entries are: pt, pts, mm, cm, in, inch, or inches.
- If you don't enter a unit of measure, Prinergy assumes the unit is the unit set in the Prinergy Workshop Preferences dialog box.
- If you do enter a unit of measure, Prinergy converts it to the unit of measure set in Prinergy Workshop Preferences dialog box. For example, if your Workshop Preferences measurement unit is inch and you enter
72 pt
, Prinergy converts it to 1 in.
- On the Raw APA File tab, the unit of measure is always points.
Example 1: Pattern matching
This example shows the use of pattern matching.
The input files, refined files, and desired geometry assignments are:
Input files | Book.pdf |
Refined files | Book.p1.pdf, Book.p2.pdf, Book.p3.pdf |
Desired geometry assignments | Set the geometry for the pages. Set Offset X and Offset Y to -36 points, Trim X to 612 points, and Trim Y to 792 points. Scaling is 100% and there is no change in orientation. |
In the Geometry Assignments view, the instruction is:
Refined file name | Offset X | Offset Y | Trim size X | Trim size Y | Scale X | Scale Y | Orientation |
---|---|---|---|---|---|---|---|
.p.pdf | -36 pt | -36 pt | 612.0 pt | 792.0 pt | 100% | 100% | 0 |
In the Raw APA File view, the instruction is:
GEOM= "[$].p[#].pdf" -36.0 -36.0 612.0 792.0 1 1 0
Example 2: Pattern matching and assigning geometry from input files
This example shows the use of pattern matching and assigning geometry from input files.
This example is has the same input files, refined files, and desired geometry assignments as in Example 1, except it uses the trim size from the input files.
In the Geometry Assignments view, the instruction is:
Refined file name | Offset X | Offset Y | Trim size X | Trim size Y | Scale X | Scale Y | Orientation |
---|---|---|---|---|---|---|---|
.p.pdf | -.5 in | -.5 in | Mixed | Mixed | 100% | 100% | 0 |
In the Raw APA File view, the instruction is:
GEOM= "[$].p[#].pdf" -36.0 -36.0 [ ] [ ] 1 1 0
Legend
Match Letters Match letters (a-z, A-Z) in the page filename. For example Match Digits Match numbers (0-9) in the page filename. For example .p.pdf matches filenames 12345.p1.pdf, 05282003.p2.pdf, and 01.p165.pdf. Match Either Match letters or numbers (a-z, A-Z, 0-9) in the page filename. For example .p.pdf matches filenames 12345.p1.pdf, ABCDE.p2.pdf, Book cover99.p76.pdf, Book052803.p205.pdf. You can also specify the number of characters that this wild card will match. This Position Indicates that this part of the page name is the same as the page position to which the page will be assigned. This Page Set (Page Set Assignment mode only) Indicates that this part of the page name is the same as the name of the page set or page set prefix to which the page will be assigned. All Page Sets (Page Set Assignment mode only) Assigns the page to the designated page position in all sets in the job. This Product (Run List Assignment mode only) Indicates that this part of the page name is the same as the name of the product. All Products (Run List Assignment mode only) Assigns the page to the designated page positions in the run lists of all the products. This Part (Run List Assignment mode only) Indicates that this part of the page name is the same as the name of the part. All Parts (Run List Assignment mode only) Assigns the page to the designated page positions in the run lists of all the parts..p1.pdf
matches filenames Book.p1.pdf, Front matter.p1.pdf, and JobXYZ.p1.pdf.
You can also specify the number of characters that this wild card will match.
To verify the number of characters that will be matched, move the cursor over the icon and check the length that is listed.
You can also specify the number of characters that this wild card will match.
To verify the number of characters that will be matched, move the cursor over the icon and check the length that is listed.
Note: .p.pdf matches the same filenames.
To verify the number of characters that will be matched, move the cursor over the icon and check the length that is listed.
For example if you enter Book.p.pdf, a matching wild card is inserted in the Position column. Book.p1.pdf is assigned to position 1, Book.p2.pdf is assigned to position 2, and so on.
For example, if you enter .p1.pdf, a matching wild card is inserted in the Page Set Name/Prefix column. Book.p1.pdf would be assigned to the Book page set.
For example, if you enter .p.pdf, a matching wild card is inserted in the Product Run List column. If your product is Book, page Book.p1.pdf will be assigned to position 1 in the Book run list, page Book.p2.pdf will be assigned to position 2 in the Book run list and so on.
For example, if you enter .p.pdf, a matching wild card is inserted in the Part Run List column. If your part is Cover, page Cover.p1.pdf will be assigned to position 1 in the Cover run list, page Cover.p2.pdf will be assigned to position 2 in the Cover run list and so on.