Sv translation | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
The following ports are used by Prinergy, and need to be open for Prinergy to work:
Note: AFP port information is given for informational purposes and legacy configurations only. AFP is not qualified with Prinergy Workflow 8.0. The Built-in Windows Firewall is not supported The software firewall that ships with Windows 2008 and Windows 2012 is not supported on a Prinergy Connect/Direct/Powerpack server. Additional Firewall considerations If there is a firewall between the Prinergy servers and the Workshop clients, it is critical that the firewall does not close idle connections after some arbitrary time period. If it does, this could result in lags or stalls in Workshop when it is forced to re-establish its connections to the server. Instead, the firewall should be configured to only close the connection if it is determined to be dead by probing to the end hosts to determine the validity of the connection. This feature is known as 'Dead Connection Detection' on Cisco firewalls. If such a feature does not exist on your chosen firewall then the idle timeout should be set to a period equal to a typical production shift and operators should be warned that Workshop may stall for up to a couple of minutes when they return to it if it has been left running but idle for a longer period. Local-Link IPv4 Subnet IP range 169.254.x.x is reserved within the IPv4 specification for Local-Link self-assigned IP addresses and is not operationally compatible with Prinergy Workflow server software. |
Sv translation | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Die folgenden Ports werden durch Prinergy verwendet und müssen geöffnet sein, damit Prinergy funktioniert:
Hinweis: Die AFP-Anschlussinformationen dienen nur Informationszwecken und früher verwendeten Konfigurationen. AFP ist nicht für Prinergy Workflow8.0 geeignet. Die integrierte Windows-Firewall wird nicht unterstützt Die Software-Firewall, die zusammen mit Windows2008 und Windows2012 geliefert wurde, wird auf einem Prinergy Connect/Direct/PowerPack-Server nicht unterstützt. |
Sv translation | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Prinergy utiliza los siguientes puertos, que deben estar abiertos para que Prinergy funcione:
Nota: La información del puerto de AFP es solamente para fines informativos y configuraciones anteriores. AFP no puede utilizarse con Prinergy Workflow 8.0. El cortafuegos integrado de Windows no es compatible El software cortafuegos que se incluye con Windows 2008 y Windows 2012 no es compatible con un servidor Prinergy Connect/Direct/Powerpack. |
Sv translation | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Prinergy utilise les ports suivants, et ceux-ci doivent être ouverts pour permettre son bon fonctionnement:
Remarque: les informations de ports AFP sont uniquement fournies à titre indicatif et pour les configurations existantes. AFP n'est pas compatible avec Prinergy Workflow8.0. Le Pare-feu Windows intégré n'est pas pris en charge Le pare-feu logiciel fourni avec Windows2008 et Windows2012 n'est pas pris en charge sur les serveurs Prinergy Connect/Direct/Powerpack. |
Sv translation | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Le seguenti porte vengono utilizzate da Prinergy e devono essere aperte affinché Prinergy funzioni correttamente:
Nota: informazioni sulla porta AFP concesse al solo scopo informativo e per configurazioni esistenti. AFP non è compatibile con Prinergy Workflow 8.0. Windows Firewall integrato non è supportato Il firewall per software fornito con Windows 2008 e Windows 2012 non è supportato su un server Prinergy Connect/Direct/Powerpack. |
Sv translation | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
以下のポートは Prinergy で使用されるので、Prinergy が操作できるようにオープンにしておく必要があります。
注意:AFP ポート情報は、情報と古い設定の提供のみを目的としています。AFP は、Prinergy Workflow 8.0 では認定されていません。 ビルトインの Windows Firewall はサポートされていません。 Windows 2008 と Windows 2012 に同梱されているソフトウェア ファイアウォールは、Prinergy Connect/Direct/Powerpack サーバーではサポートされていません。 |
Sv translation | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
印能捷使用以下端口,需要打开这些端口印能捷才能工作:
注意:AFP 端口信息仅供参考和用于旧配置。AFP 不适用于印能捷 Workflow 8.0。 不支持内置 Windows 防火墙 印能捷 Connect/Direct/强力包装版服务器不支持 Windows 2008 和 Windows 2012 随附的软件防火墙。 |