Sv translation | ||
---|---|---|
| ||
Prinergy can generate PDF/X-1a:2001 and PDF/X-3:2003 files. Outputting to PDF/X If you are intending to output PDF/X, you must first choose Refine to PDF/X, rather than just outputting to PDF/X. Prinergy detects and deals with many PDF/X issues at the refine stage. When you select a PDF/X format when outputting, Prinergy checks the master files for PDF/X conformance. However, some issues, including font embedding, image replacement, and color conversion cannot be handled on output and cause Prinergy to fail the file. What are the flavors of PDF/X? PDF/X-1 family: PDF/X-1:1999—approved by ANSI (American National Standards Institute) as PDF/X-1 in October 1999. This format is based on PDF 1.2 plus Adobe Tech Note 5188. Technical requirements of PDF/X-1a:2001 and PDF/X-3:2003
What happens during refining? When you refine to PDF/X, the Normalize, Optimize, and ColorConvert options in the refine process template must be selected. CAUTION: If you have a L*a*b* PANTONE color library installed, selecting the Look Up Recipe in Color Database option in the Source of Color Recipes area of the Spot Color Handling section may cause Prinergy to fail the file. If the option is not selected, and color recipes are defined using L*a*b*, Prinergy may also fail the file. L*a*b* color space is not allowed for PDF/X-1a:2001 and PDF/X-3:2003 files. During optimization, Prinergy checks for the remaining PDF/X issues. If it is not possible to create a PDF/X-compliant file, Prinergy fails the file. What happens when I select PDF/X-1a:2001 when outputting in Prinergy? The selected master files are checked for PDF/X-1a:2001 conformance, in case a master file was edited and a non-PDF/X-1a:2001 element or characteristic was introduced into the file. Some issues are corrected at this point. However, some issues —including font embedding, image replacement, and color conversion— cannot be handled at this point and cause Prinergy to fail the file. The file must then be refined to PDF/X-1a:2001 again. What is the recommended workflow? It is important to refine to PDF/X, because it ensures that your proof cycle is based on the same PDF/X file that is output and sent to the printer site.
Can I simply refine files to PDF as usual, and then output to PDF/X-1a:2001 on Vector JTP output? Though it might be possible to do so in some cases, in general this is not the recommended way of working. In particular, color matching must be performed during refine. A file needing color matching will not be converted to PDF/X-1a:2001 on output if it has not been refined to PDF/X-1a:2001. Other issues addressed during refine include font embedding and OPI. What happens during vector output (Publish PDF or Vector JTP)? When you select PDF/X when outputting in Prinergy, the selected master files are checked for PDF/X conformance. This is in case a master file has been edited and a non-PDF/X element or characteristic has been introduced into the file. Some issues will be corrected at this point, but some issues—including font embedding, image replacement, and color conversion—cannot be handled at this point and will cause Prinergy to fail the file. The file must be refined to PDF/X again. Must I do OPI replacement? PDF/X-1a:2001 requires that files not contain OPI comments. The expectation is that OPI replacement was done and that the receiver of the PDF/X file needs no additional external resources (fonts or images) to process the file. Can I refine a PDF/X-1a:2001 file? Yes. Prinergy treats a PDF/X-1a:2001 file like any PDF input file. The file can be refined to a regular PDF file, or it can be refined to a PDF/X-1a:2001 file again. If it is refined to a regular PDF file, it no longer has the PDF/X-1a:2001 identification keys. If it is refined to PDF/X-1a:2001, Prinergy checks it the same as any other input file that is refined to PDF/X-1a:2001. What about PDF/X checkers? Kodak has tested the following PDF/X checkers:
In our testing, our PDF/X-1a output consistently passes the Apago and DDAP checkers.
Are there any known issues with the implementation of PDF/X-1a:2001 in Prinergy? If a PDF/X page that has the Trapped key set to true is brought into Prinergy and refined with the Trap section of the process template enabled, Prinergy tries to retrap the page. What if I don't want to use the PDF/X feature in Prinergy? If you don't want to use PDF/X format as your digital master file, simply configure your process template to generate PDF instead of PDF/X-1a:2001. Prinergy generates digital master files the way it always does. This allows the Prinergy functionality that is not possible with PDF/X. What about PDF/X-3? A PDF/X-3 file can contain Output Intents, which indicate the file's intended target device, including its color profile. What about PDF/X-4? Prinergy 8.4 is can be used to verify PDF/X-4 input files via Preflight+. Where can I find more information about PDF/X?
|
Sv translation | ||
---|---|---|
| ||
Prinergy peut générer des fichiers PDF/X-1a:2001 et PDF/X-3:2003. Sortie PDF/X Si vous avez l'intention de produire des fichiers PDF/X, vous devez d'abord choisir l'option Raffiner en PDF/X, plutôt que de générer uniquement des fichiers PDF/X. Prinergy détecte et traite nombre des problèmes PDF/X lors de l’étape de raffinage. Si vous sélectionnez un format PDF/X lors de la sortie, Prinergy vérifie la conformité des fichiers maîtres avec le format PDF/X. Cependant, certains problèmes, tels que l'incorporation des polices, le remplacement d'images et la conversion des couleurs, ne peuvent pas être résolus au stade de la sortie et Prinergy est incapable de traiter correctement le fichier. Différents types de PDF/X PDF/X-1 famille : PDF/X-1:1999 : approuvé par l'ANSI (American National Standards Institute) en tant que PDF/X-1 en octobre 1999. Ce format est basé sur PDF 1.2 et Adobe Tech Note 5188. Caractéristiques techniques des formats PDF/X-1a:2001 et PDF/X-3:2003
Quelles sont les étapes du processus de raffinage ? Lorsque vous raffinez au format PDF/X, les options Normalisation, Optimisation et ColorConvert du modèle de processus de raffinage doivent être sélectionnées. ATTENTION : Si vous avez installé une bibliothèque de couleurs L*a*b* PANTONE et que vous choisissez l'option Rechercher une formule dans la base de données de couleurs dans la zone Source des formules de couleurs de la section Gestion des couleurs d'accompagnement, Prinergy risque de ne pas pouvoir traiter correctement le fichier. Si vous ne choisissez pas cette option et que les formules de couleurs ont été définies à l'aide de L*a*b*, Prinergy risque également de ne pas être en mesure de traiter correctement le fichier. L'espace colorimétrique L*a*b* n'est pas autorisé pour les fichiers PDF/X-1a:2001 et PDF/X-3:2003. Durant l'optimisation, Prinergy vérifie les problèmes PDF/X subsistants. S'il est impossible de créer un fichier compatible PDF/X, Prinergy ne crée pas de fichier. Si PDF/X-1a:2001 est sélectionné lors de la sortie dans Prinergy Quand un fichier maître a été modifié et qu'un élément ou une caractéristique non-PDF/X a été introduit(e) dans le fichier, la conformité des fichiers maîtres sélectionnés est vérifiée pour PDF/X-1a:2001. Certains problèmes sont alors corrigés. Cependant, certains problèmes, tels que l'incorporation des polices, le remplacement d'images et la conversion des couleurs, ne peuvent pas être résolus à ce stade et Prinergy est incapable de traiter correctement le fichier. Le fichier doit ensuite être raffiné à nouveau en PDF/X-1a:2001. Flux de production recommandé Il est important de raffiner en PDF/X, car cela permet d'assurer que le cycle d'épreuves est basé sur le même fichier PDF/X généré et envoyé au site d'impression.
Possibilité de raffiner les fichiers en PDF comme habituellement, puis de les générer en PDF/X-1a:2001 sur JTP de sortie vectorielle Bien qu'il soit parfois possible de le faire, cela n'est généralement pas la méthode de travail recommandée. Le contretypage des couleurs, en particulier, doit être réalisé pendant le raffinage. Un fichier nécessitant un contretypage des couleurs ne sera pas converti en PDF/X-1a:2001 à la sortie s'il n'a pas été raffiné en PDF/X-1a:2001. D'autres problèmes tels que l'incorporation des polices et l'OPI, peuvent survenir pendant le raffinage. Quelles sont les étapes du processus de sortie vectorielle (publication au format PDF ou JTP vectoriel) ? Lorsque vous sélectionnez PDF/X durant la sortie dans Prinergy, la compatibilité PDF/X des fichiers maîtres sélectionnés est vérifiée. C'est le cas quand un fichier maître a été modifié et qu'un élément ou une caractéristique non-PDF/X a été introduit(e) dans le fichier. Certains problèmes peuvent être corrigés, mais certains autres tels que l'incorporation des polices, le remplacement d'images et la conversion des couleurs ne peuvent pas être résolus à ce stade et Prinergy est incapable de traiter correctement le fichier. Le fichier doit être raffiné une nouvelle fois en PDF/X. Nécessité de remplacer l'OPI Les fichiers traités par PDF/X-1a:2001 ne doivent pas contenir de commentaires OPI. La substitution OPI doit avoir été effectuée et le destinataire du fichier PDF/X n'a pas besoin de ressources externes supplémentaires (polices ou images) pour traiter le fichier. Puis-je raffiner un fichier PDF/X-1a:2001 ? Oui. Prinergy traite un fichier PDF/X-1a:2001 comme n'importe quel fichier d'entrée PDF. Le fichier peut être raffiné en fichier PDF standard ou à nouveau en fichier PDF/X-1a:2001. S'il est raffiné en fichier PDF standard, il ne contient plus les clés d'identification PDF/X-1a:2001. S'il est raffiné en PDF/X-1a:2001, Prinergy s'assure qu'il est identique à un autre fichier d'entrée raffiné en PDF/X-1a:2001. À propos des vérificateurs PDF/X Kodak a testé les vérificateurs PDF/X suivants :
Lors de nos tests, notre sortie PDF/X-1a réussit toujours les vérificateurs Apago et DDAP.
Existe-t-il des problèmes connus concernant la mise en application de la fonction PDF/X-1a:2001 dans Prinergy ? Si une page PDF/X dont la clé Recouvert est définie sur vrai est importée dans Prinergy et raffinée à l'aide de la section Recouvrement du modèle de processus activé, Prinergy essaie d'effectuer un nouveau recouvrement de la page. Et si je ne souhaite pas utiliser la fonction PDF/X de Prinergy ? Si vous ne souhaitez pas utiliser le format PDF/X pour votre fichier maître numérique, configurez simplement votre modèle de processus de manière à générer un fichier PDF plutôt qu'un fichier PDF/X-1a:2001. Prinergy génère les fichiers maîtres numériques de la manière habituelle. Cela vous permet d'utiliser la fonction Prinergy qui n'est pas utilisable avec PDF/X. À propos de PDF/X-3 Un fichier PDF/X-3 peut contenir des intentions de sortie, qui indiquent le périphérique cible du fichier, y compris son profil de couleur. À propos de PDF/X-4 Prinergy 8.4 peut être utilisé pour vérifier des fichiers d'entrée PDF/X-4 via Preflight+. Où puis-je trouver plus d'informations sur PDF/X ?
|
Sv translation | ||
---|---|---|
| ||
印能捷可以生成 PDF/X-1a:2001 和 PDF/X-3:2003 文件。 输出到 PDF/X 如果要输出 PDF/X,必须先选择精炼为 PDF/X,而不是只输出到 PDF/X。印能捷在精炼阶段检测和处理许多 PDF/X 问题。在输出时选择 PDF/X 格式时,印能捷会检查主文件的 PDF/X 一致性。但是,诸如字体嵌入、图像替换和颜色转换等问题无法在输出时处理,会导致印能捷无法处理文件。 PDF/X 有哪些特性? PDF/X-1 系列: PDF/X-1:1999 — 由 ANSI(美国国家标准协会)于 1999 年 10 月批准为 PDF/X-1。此格式基于 PDF 1.2 和 Adobe Tech Note 5188。 PDF/X-1a:2001 和 PDF/X-3:2003 的技术要求
在精炼期间会发生什么? 精炼为 PDF/X 时,必须选择精炼处理模板中的规范化、优化和颜色转换选项。 注意:如果您安装了 L*a*b* PANTONE 颜色库,在专色处理部分的颜色配置源区域中选择查找颜色数据库中的配置可能会导致印能捷无法处理文件。如果未选择该选项,并且颜色配置是使用 L*a*b* 定义的,则印能捷也可能会无法处理文件。对于 PDF/X-1a:2001 和 PDF/X-3:2003 文件,不允许使用 L*a*b* 颜色空间。 在优化过程中,印能捷会检查剩余的 PDF/X 问题。如果无法创建符合 PDF/X 的文件,印能捷会无法处理文件。 在印能捷中输出时,如果选择 PDF/X-1a:2001, 会发生什么? 如果已编辑主文件,并且文件中引入了非 PDF/X-1a:2001 元素或特征,则会检查选定的主文件是否符合 PDF/X-1a:2001 规范。此时已更正某些问题。但是,诸如字体嵌入、图像替换和颜色转换等问题无法在输出时处理,会导致印能捷无法处理文件。然后,必须将该文件再次精炼为 PDF/X-1a:2001。 建议的工作流程是什么? 精炼为 PDF/X 非常重要,因为它可以确保打样周期基于输出并发送到印刷机站点的相同 PDF/X 文件。
能否像平常一样将文件精炼为 PDF,然后在矢量 JTP 输出上输出为 PDF/X-1a:2001? 虽然在某些情况下可能采取这样的工作方式,但通常不建议这么做。特别是,必须在精炼过程中执行颜色匹配。如果需要颜色匹配的文件未精炼为 PDF/X-1a:2001,则在输出时不会转换为 PDF/X-1a:2001。精炼过程中解决的其他问题包括字体嵌入和 OPI。 在矢量输出(发布 PDF 或矢量 JTP)期间会发生什么? 在印能捷中输出时选择 PDF/X 时,会检查选定的主文件是否符合 PDF/X。如果已编辑主文件,并且文件中引入了非 PDF/X 元素或特征,则会出现这种情况。部分问题会在此时得到纠正,但是,诸如字体嵌入、图像替换和颜色转换等问题无法在此时处理,会导致印能捷无法处理文件。文件必须再次精炼为 PDF/X。 是否必须进行 OPI 替换? PDF/X-1a:2001 要求文件不包含 OPI 注释。期望 OPI 替换已完成,并且 PDF/X 文件的接收者不需要其他外部资源(字体或图像)来处理文件。 是否可以精炼 PDF/X-1a:2001 文件? 是。印能捷将 PDF/X-1a:2001 文件视为任何 PDF 输入文件。该文件可以精炼为常规 PDF 文件,也可以重新精炼为 PDF/X-1a:2001 文件。如果精炼为常规 PDF 文件,则不再具有 PDF/X-1a:2001 识别码。如果精炼为 PDF/X-1a:2001, 印能捷将检查它是否与精炼为 PDF/X-1a:2001 的任何其他输入文件相同。 PDF/X 检查器如何? Kodak 已测试了以下 PDF/X 检查器:
在我们的测试中,我们的 PDF/X-1a 输出始终通过 Apago 和 DDAP 检查器。
在印能捷中实施 PDF/X-1a:2001 时是否存在任何已知问题? 如果将陷印键设为“真”的 PDF/X 页面放入印能捷并在启用了处理模板的陷印部分时进行精炼,印能捷将尝试重新陷印该页面。 如果我不想在印能捷中使用 PDF/X 功能该怎么办? 如果不想将 PDF/X 格式用作数字主文件,只需配置处理模板以生成 PDF 而不是 PDF/X-1a:2001。印能捷始终以同样的方式生成数字主文件。这允许使用 PDF/X 不支持的印能捷功能。 PDF/X-3 如何? PDF/X-3 文件中可以包含输出意向,它指示文件的目标设备,包括其颜色配置文件。 PDF/X-4 如何? 印能捷 8.4 可用于通过 Preflight+ 验证 PDF/X-4 输入文件。 从何处可以获得关于 PDF/X 的更多信息?
|
Sv translation | ||
---|---|---|
| ||
Prinergy kann PDF/X-1a:2001- und PDF/X-3:2003-Dateien erzeugen. Ausgabe als PDF/X Wenn Sie eine PDF/X-Ausgabe planen, müssen Sie zunächst ein Refining der PDF/X-Daten durchführen, anstatt sie lediglich im Format PDF/X auszugeben. Prinergy erkennt und löst zahlreiche PDF/X-Probleme während der Refine-Phase. Wenn Sie bei der Ausgabe ein PDF/X-Format auswählen, überprüft Prinergy, ob die Master-Dateien alle Anforderungen für PDF/X erfüllen. Einige Probleme, wie das Einbetten von Schriftarten, der Austausch von Bildern und die Farbkonvertierung, können bei der Ausgabe nicht bewältigt werden, so dass die Datei nicht verarbeitet werden kann. Welche Varianten von PDF/X gibt es? PDF/X-1-Familie: PDF/X-1:1999 – genehmigt von ANSI (American National Standards Institute) als PDF/X-1 im Oktober 1999. Dieses Format basiert auf PDF 1.2 sowie Adobe Tech Note 5188. Technische Voraussetzungen für PDF/X-1a:2001 und PDF/X-3:2003
Was geschieht während des Refinens? Wenn Sie ein Refining zu PDF/X durchführen, müssen die Optionen Normalisieren, Optimieren und ColorConvert in der Refining-Prozessvorlage aktiviert sein. VORSICHT: Wenn Sie eine L*a*b*-PANTONE-Farbbibliothek installiert haben, kann Prinergy die Datei bei Auswahl der im Unterbereich Quelle der Ersatzfarben des Bereichs Sonderfarbenbehandlung wählbaren Option Ersatzfarbe in Farbdatenbank suchen möglicherweise nicht verarbeiten. Wenn die Option nicht ausgewählt ist und die Farbrezepturen in der Datei mit L*a*b* definiert wurden, kann die Datei möglicherweise ebenfalls nicht in Prinergy verarbeitet werden. Der L*a*b*-Farbraum ist für PDF/X-1a:2001- und PDF/X-3:2003-Dateien nicht zulässig. Bei der Optimierung überprüft Prinergy die Datei auf weitere mögliche PDF/X-Probleme. Falls es nicht möglich ist, eine PDF/X-kompatible Datei zu erstellen, kann Prinergy die Datei nicht verarbeiten. Was geschieht, wenn ich zur Ausgabe in Prinergy PDF/X-1a:2001 auswähle? Die ausgewählten Masterdateien werden auf PDF/X-1a:2001-Konformität geprüft. Dabei soll erkannt werden, ob bei der Bearbeitung einer Masterdatei ein Element oder Merkmal, das nicht PDF/X-1a:2001 entspricht, in die Datei eingefügt wurde. Zu diesem Zeitpunkt werden einige Fehler korrigiert. Einige Probleme, wie das Einbetten von Schriftarten, der Austausch von Bildern und die Farbkonvertierung, können zu diesem Zeitpunkt nicht bewältigt werden, so dass die Verarbeitung der Datei von Prinergy abgebrochen wird. Die Datei muss erneut zu PDF/X-1a:2001 refined werden. Welcher Workflow wird empfohlen? Das Refinen zu PDF/X ist ein wichtiger Schritt, der sicherstellt, dass Ihr Proof-Zyklus auf der gleichen PDF/X-Datei basiert, die ausgegeben und an den Druckerstandort gesendet wird.
Kann ich Dateien einfach wie gehabt zu PDF refinen und anschließend als Vektor-JTP nach PDF/X-1a:2001 ausgeben? Dies kann in bestimmten Fällen möglich sein, diese Vorgehensweise wird jedoch im Allgemeinen nicht empfohlen. Während des Refine-Vorgangs muss insbesondere die Farbanpassung erfolgen. Eine Datei, in der eine Farbanpassung erforderlich ist, wird bei der Ausgabe nicht in PDF/X-1a:2001 konvertiert, wenn sie nicht zu PDF/X-1a:2001 refined wurde. Das Einbetten von Schriftarten und OPI kann zu weiteren Problemen während des Refine-Vorgangs führen. Was geschieht während der Vektorausgabe (Herausgeben von PDF oder Vektor-JTP)? Wenn Sie PDF/X für die Ausgabe in Prinergy festlegen, werden die ausgewählten Masterdateien auf PDF/X-Konformität überprüft. Dadurch wird überprüft, ob beim Bearbeiten einer Master-Datei ein Nicht-PDF/X-Element oder eine nicht zugehörige Eigenschaft in die Datei eingefügt wurde. Einige Probleme werden zu diesem Zeitpunkt korrigiert, andere (z. B. Schriftarteinbettung, Bildersetzung und Farbkonvertierung) können zu diesem Zeitpunkt jedoch nicht behoben werden und führen dazu, dass Prinergy die Verarbeitung der Datei abbricht. Die Datei muss erneut zu PDF/X refined werden. Muss ich eine OPI-Ersetzung durchführen? Für PDF/X-1a:2001 dürfen Dateien keine OPI-Kommentare enthalten. Es wird erwartet, dass eine OPI-Ersetzung stattgefunden hat und der Empfänger der PDF/X-Datei zur Verarbeitung der Datei keine zusätzlichen externen Ressourcen (Schriftarten oder Bilder) benötigt. Kann ich eine PDF/X-1a:2001-Datei refinen? Ja. Prinergy behandelt eine PDF/X-1a:2001-Datei wie jede andere PDF-Eingabedatei auch. Die Datei kann zu einer normalen PDF-Datei oder wieder zu einer PDF/X-1a:2001-Datei refined werden. Wenn sie zu einer normalen PDF-Datei refined wird, verliert sie die PDF/X-1a:2001-Identifikationsschlüssel. Wenn die Datei zu PDF/X-1a:2001 refined wird, führt Prinergy die gleichen Prüfungen wie bei allen anderen Eingabedateien durch, die zu PDF/X-1a:2001 refined werden. Was ist mit PDF/X-Prüfprogrammen? Kodak hat die folgenden PDF/X-Prüfprogramme getestet:
Bei unseren Tests haben unsere PDF/X-1a-Ausgaben die Tests der Apago- und DDAP-Prüfprogramme durchgehend bestanden.
Sind Probleme mit der Implementierung von PDF/X-1a:2001 in Prinergy bekannt? Wenn eine PDF/X-Seite, für die der Schlüssel „Trapped“ auf „wahr“ gesetzt ist, in Prinergy eingefügt und refined wird, während der Bereich Trap der Prozessvorlage aktiviert ist, versucht Prinergy, die Seite erneut zu trappen. Was mache ich, wenn ich die PDF/X-Funktion in Prinergy nicht verwenden möchte? Wenn Sie das PDF/X-Format nicht als digitale Masterdatei verwenden möchten, konfigurieren Sie Ihre Prozessvorlage einfach so, dass PDF anstelle von PDF/X-1a:2001 generiert wird. Prinergy generiert digitale Masterdateien wie üblich. Dadurch können Prinergy-Funktionen verwendet werden, die mit PDF/X nicht möglich sind. Was passiert mit PDF/X-3? Eine PDF/X-3-Datei kann Ausgabepläne enthalten, in denen das vorgesehene Zielgerät der Datei einschließlich des Farbprofils angegeben ist. Was passiert mit PDF/X-4? Prinergy 8.4 kann zur Überprüfung von PDF/X-4-Eingabedateien über Preflight+ verwendet werden. Wo finde ich weitere Informationen über PDF/X?
|
Sv translation | ||
---|---|---|
| ||
Prinergy では、PDF/X-1a:2001 ファイルおよび PDF/X-3:2003 ファイルを生成できます。この機能にはライセンスが必要です。 PDF/X への出力 PDF/X に出力する場合、単に PDF/X に出力するだけでなく、初めに PDF/X へのリファインを行う必要があります。Prinergy では、リファイン段階で多数の PDF/X の問題点が検出され、これらの問題が対処されます。出力に PDF/X を選択すると、選択されたマスタ ファイルが PDF/X に準拠しているかどうかチェックされます。ただし、フォントの埋め込み、画像の置換、カラー変換などの問題には、出力時には対処できず、Prinergy でファイルの処理エラーが発生します。 PDF/X の特徴 PDF/X-1 ファミリー: PDF/X-1:1999 - ANSI(米国規格協会)により PDF/X-1 として 1999 年 10 月に承認されました。この形式は、PDF 1.2 に Adobe Tech Note 5188 を加えたものを基礎にしています。 PDF/X-1a:2001 および PDF/X-3:2003 の技術要件
リファイン時の処理 PDF/X にリファインする際には、リファイン プロセス テンプレートの[ノーマライズ]、[オプティマイズ]、および[カラー変換]オプションを選択する必要があります。 注意:L*a*b* PANTONE カラー ライブラリがインストールされている場合は、[スポット カラーの処理]セクションの[カラー レシピのソース]領域で[カラー データベースでレシピを検索]オプションをオンにすると、ファイルを処理できない場合があります。このオプションがオフで、L*a*b* を使用してカラー レシピが定義されている場合も、ファイルを処理できない場合があります。L*a*b カラー スペースは、PDF/X-1a:2001 および PDF/X-3:2003 ファイルに使用することはできません。 残りの PDF/X 準拠項目はオプティマイズ中にチェックされます。PDF/X 準拠ファイルの作成が可能ではない場合、ファイルにエラーが発生します。 Prinergy での出力時に PDF/X-1a:2001 を選択した場合に実行される内容 編集により PDF/X-1a:2001 以外のエレメントや機能が追加されている場合に備えて、選択したマスタ ファイルが PDF/X-1a:2001 に準拠しているかどうかチェックされます。この時点でいくつかの問題が修正されます。ただし、フォントの埋め込み、画像の置換、カラー変換などの問題は、この時点では対処できず、Prinergy でのファイル処理エラーの原因になります。ファイルは、PDF/X-1a:2001 に再度リファインする必要があります。 推奨ワークフロー PDF/X にリファインする作業は重要です。それにより、出力および印刷会社への送信に使用するのと同じ PDF/X ファイルをベースとするプルーフ サイクルが行われることになるためです。
ファイルを通常どおり PDF にリファインし、ベクター JTP 出力で PDF/X-1a:2001 に出力する方法 この出力方法は一部の状況で選択可能ですが、一般にお勧めできる処理ではありません。特に、リファイン時にカラー マッチングを実行する必要があります。カラー マッチングを必要とするファイルを PDF/X-1a:2001 にリファインしていない場合は、出力時に PDF/X-1a:2001 に変換されません。リファイン時に対処されるその他の問題として、フォントの埋め込みと OPI があります。 ベクター出力(PDF の発行またはベクター JTP 出力)時に実行される内容 Prinergy での出力に PDF/X を選択すると、選択されたマスタ ファイルが PDF/X に準拠しているかどうかチェックされます。これは、マスタ ファイルが編集され、PDF/X ではないエレメントや設定がファイルに追加された場合に備えるための処理です。この時点で修正される問題もありますが、一部の問題(フォントの埋め込み、画像の置換、およびカラー変換など)はここでは解決されず、Prinergy でファイルの処理エラーが発生します。ファイルは、PDF/X に再度リファインする必要があります。 OPI 置換の必要性 PDF/X-1a:2001 では、ファイルに OPI コンポーネントが含まれていないことが必須条件です。OPI が置換済みで、PDF/X ファイルの受信者がファイルを処理する際に他の外部リソース(フォントまたは画像)を必要としないことが求められています。 PDF/X-1a:2001 ファイルのリファイン はい。Prinergy は、PDF/X-1a:2001 を他の PDF 入力ファイルと同等に扱います。PDF/X-1a:2001 ファイルを通常の PDF ファイルにリファインすることも、再度 PDF/X-1a:2001 ファイルにリファインすることもできます。通常の PDF ファイルにリファインすると、そのファイルは PDF/X-1a:2001 識別キーを持たなくなります。PDF/X-1a:2001 にリファインすると、Prinergy はその他の入力ファイルを PDF/X-1a:2001 にリファインした場合と同様にそのファイルをチェックします。 PDF/X チェッカーについて コダックでは、次の PDF/X チェッカーのテストを実施しました。
当社のテストでは、コダックの PDF/X-1a 出力は Apago チェッカーと DDAP チェッカーで常に合格しました。
Prinergy での PDF/X-1a:2001 の実装に関する現在の問題点 [トラップされている]が True に設定されている PDF/X ページを Prinergy に入力して、[トラップ]セクションが有効のプロセス テンプレートでリファインすると、Prinergy はそのページの再トラップを試行します。 Prinergy で PDF/X 機能を使用しない場合 デジタル マスタ ファイルとして PDF/X 形式を使用しない場合は、PDF/X-1a:2001 でなく PDF を生成するようにプロセス テンプレートを設定します。Prinergy は、通常の方法でデジタル マスタ ファイルを作成します。これにより、PDF/X では使用できない Prinergy の機能を使用できます。 PDF/X-3 について PDF/X-3 ファイルには、ターゲット デバイスを指定する出力インテントやカラー プロファイルを含めることができます。 PDF/X-4 について Prinergy 8.4 は、Preflight+ 経由で PDF/X-4 入力ファイルを確認するために使用できます。 PDF/X の詳細情報
|
Sv translation | ||
---|---|---|
| ||
Prinergy puede generar archivos PDF/X-1a:2001 y PDF/X-3:2003. Generación de salidas como PDF/X Si desea generar salidas PDF/X, primero debe elegir el afinado a PDF/X, en lugar de generar la salida PDF/X directamente. Prinergy detecta y soluciona muchos de los problemas de PDF/X en la etapa de afinado. Cuando selecciona un formato PDF/X para la salida, Prinergy comprueba si los archivos máster cumplen los criterios de PDF/X. Sin embargo, algunos problemas, como la incrustación de fuentes, la sustitución de imágenes y la conversión de color, no pueden gestionarse en la salida y provocarán que falle el archivo en Prinergy. ¿Cuáles son los sabores de PDF/X? Familia PDF/X-1: PDF/X-1:1999: aprobado por ANSI (American National Standards Institute) como PDF/X-1 en octubre de 1999. Este formato se basa en PDF 1.2 y Adobe Tech Note 5188. Requisitos técnicos de PDF/X-1a:2001 y PDF/X-3:2003
Descripción del proceso de afinado Cuando se afina como PDF/X, se deben seleccionar las opciones Normalizar, Optimizar y ColorConvert en la plantilla de proceso de afinado. PRECAUCIÓN: Si tiene instalada una biblioteca de colores L*a*b* PANTONE, la opción Buscar receta en la base de datos de colores del área Origen de las recetas de color que se encuentra en la sección Gestión de colores planos puede hacer que falle el archivo en Prinergy. Si la opción no se encuentra seleccionada y se definen recetas de colores mediante L*a*b*, también puede fallar el archivo en Prinergy. El espacio cromático L*a*b* no se permite en archivos PDF/X-1a:2001 ni PDF/X-3:2003. Durante la optimización, Prinergy comprueba si sigue habiendo algún problema relacionado con PDF/X. Si no es posible generar un archivo compatible con PDF/X, fallará el archivo en Prinergy. ¿Qué ocurre al seleccionar PDF/X-1a:2001 cuando genero una salida en Prinergy? Los archivos máster seleccionados se comprueban para observar la compatibilidad de PDF/X-1a:2001, por si se ha editado un archivo máster y por si se ha introducido en el archivo un elemento o una característica que no es PDF/X-1a:2001. Algunos de los problemas se corrigen en este punto. Sin embargo, algunos problemas, como el incrustado de fuentes, la sustitución de imágenes y la conversión de color, no pueden gestionarse en este punto y provocan que falle el archivo en Prinergy. El archivo deberá afinarse de nuevo como PDF/X-1a:2001. ¿Cuál es el flujo de trabajo recomendado? Es importante afinar a PDF/X porque garantiza que el ciclo de pruebas se base en el mismo archivo PDF/X en el que se genera la salida y que se envía al sitio de la impresora.
¿Puedo afinar los archivos a PDF siguiendo el procedimiento normal y, a continuación, generar una salida a PDF/X-1a:2001 en la salida JTP vectorial? Aunque podría hacerse en algunos casos, por lo general, no es el método recomendado de trabajo. Concretamente, la correspondencia cromática se puede realizar durante el afinado. Los archivos que necesiten correspondencia cromática no se convertirán a PDF/X-1a:2001 en la salida si no han sido afinados a PDF/X-1a:2001. Otros problemas del proceso de afinado son el incrustado de fuentes y OPI. Descripción del proceso de salida vectorial (Publicar archivos PDF o JTP vectorial) Cuando se selecciona PDF/X al generar una salida en Prinergy, se comprueban los archivos máster seleccionados para determinar si son compatibles con PDF/X, por si se da el caso de que se haya modificado un archivo máster y se haya introducido en él un elemento o característica ajenos a PDF/X. Algunos problemas se corregirán en este momento, pero otros como la incrustación de fuentes, el reemplazo de imágenes y la conversión de colores no podrán gestionarse en este punto y harán que falle el archivo en Prinergy. El archivo deberá afinarse de nuevo como PDF/X. ¿Debo realizar una sustitución de OPI? Los archivos de PDF/X-1a:2001 no pueden contener comentarios OPI. Se espera que la sustitución OPI ya se haya realizado y que el receptor del archivo PDF/X no necesite recursos externos adicionales (fuentes o imágenes) para procesar el archivo. ¿Puedo afinar un archivo PDF/X-1a:2001? Sí. Prinergy trata los archivos PDF/X-1a:2001 como si fuera un archivo de entrada PDF. Este archivo se puede afinar a un archivo PDF normal o a otro archivo PDF/X-1a:2001. Si se afina a un archivo PDF normal, ya no tendrá las claves de identificación PDF/X-1a:2001. Si se afina a PDF/X-1a:2001, Prinergy lo comprueba como haría con cualquier archivo de entrada afinado a PDF/X-1a:2001. Información acerca de los verificadores PDF/X Kodak ha probado los siguientes verificadores PDF/X:
En las pruebas, la salida PDF/X-1a pasa de forma satisfactoria y coherente los verificadores Apago y DDAP.
¿Existen problemas conocidos relacionados con la implementación de PDF/X-1a:2001 en Prinergy? Si una página PDF/X, que tiene la clave Solapada se encuentra definida en true, se importa a Prinergy y se afina con la sección activada Solapar de la plantilla de proceso, Prinergy trata de volver a solapar la página. ¿Qué ocurre si no deseo utilizar la función PDF/X de Prinergy? Si no desea utilizar el formato PDF/X como archivo máster digital, configure la plantilla de proceso para generar PDF en lugar de PDF/X-1a:2001. Prinergy genera archivos máster digitales del modo en que suele hacerlo. Así se permite la funcionalidad Prinergy que no es posible con PDF/X. Información acerca de PDF/X-3 Un archivo PDF/X-3 puede contener intentos de salida, lo que indica el dispositivo de destino previsto para el archivo, incluido su perfil de color. Información acerca de PDF/X-4 Prinergy 8.4 se puede utilizar para verificar los archivos de entrada PDF/X-4 a través de Preflight+. ¿Dónde puedo obtener más información acerca de PDF/X?
|
Sv translation | ||
---|---|---|
| ||
Prinergy può generale i file PDF/X-1a:2001 e PDF/X-3:2003. Output su PDF/X Se si intende eseguire l'output PDF/X, è necessario prima scegliere Ridefinisci in PDF/X, invece di limitarsi a eseguire l'output su PDF/X. Prinergy rileva e gestisce numerosi problemi relativi al formato PDF/X nella fase di rifinitura. Quando si seleziona un formato PDF/X durante l'output, Prinergy controlla la conformità dei file master per PDF/X. Alcuni problemi, quali l'incorporamento di font, la sostituzione di immagini e la conversione dei colori, tuttavia non possono essere gestiti durante l'output e determinano l'interruzione dell'elaborazione del file. Quali sono le caratteristiche di PDF/X? Famiglia PDF/X-1: PDF/X-1:1999: approvato da ANSI (American National Standards Institute) come PDF/X-1 nell'ottobre 1999. Questo formato è basato su PDF 1.2 e Adobe Tech Note 5188. Requisiti tecnici per PDF/X-1a:2001 e PDF/X-3:2003
Cosa accade durante il processo di rifinitura? Quando si rifinisce in PDF/X, le opzioni Normalizza, Ottimizza e ColorConvert nel modello di processo di rifinitura devono essere selezionate. ATTENZIONE: se si dispone di una libreria di colori PANTONE L*a*b* installata, selezionando l'opzione Ricerca composizione nel database dei colori nell'area Origine composizioni colori della sezione Gestione tinte piatte, il file potrebbe non funzionare con Prinergy. Se l'opzione non è selezionata e le composizioni colore vengono definite utilizzando L*a*b*, è possibile che il file non sia supportato anche in Prinergy. Lo spazio colore L*a*b non è consentito nei file PDF/X-1a:2001 e PDF/X-3:2003. Durante l'ottimizzazione, Prinergy verifica gli altri eventuali problemi che potrebbero verificarsi con il formato PDF/X. Se non è possibile creare un file compatibile con il formato PDF/X, Prinergy non sarà in grado di supportare il file. Cosa succede quando si seleziona PDF/X-1a:2001 durante l'output in Prinergy? I file master selezionati vengono controllati per verificare la conformità PDF/X-1a:2001, nel caso in cui un file master sia stato modificato e nel file sia stato introdotto un elemento o una caratteristica non PDF/X-1a:2001. A questo punto, alcuni problemi sono stati corretti. Alcuni problemi, quali l'incorporamento di font, la sostituzione di immagini e la conversione dei colori, tuttavia non possono essere gestiti in questa fase e determinano l'interruzione dell'elaborazione del file. Il file deve quindi essere nuovamente rifinito in PDF/X-1a:2001. Qual è il flusso di lavoro consigliato? Rifinire in PDF/X è importante poiché garantisce che il ciclo di prova si basi sullo stesso file PDF/X di output che viene inviato al sito della stampante.
È possibile rifinire i file in PDF come di consueto e quindi stamparli in formato PDF/X-1a:2001 sull'output JTP vettoriale? Anche se in alcuni casi potrebbe essere possibile farlo, in generale questo non è il modo di procedere consigliato. In particolare, la corrispondenza dei colori deve essere eseguita durante la rifinitura. Un file che necessita della corrispondenza colori non verrà convertito in PDF/X-1a:2001 all'output se non è stato rifinito in PDF/X-1a:2001. Altri problemi risolti durante la rifinitura includono l'incorporamento di font e OPI. Cosa succede durante l'output vettoriale (Pubblica file PDF o JTP vettoriale)? Quando si seleziona PDF/X durante l'output in Prinergy, i file master selezionati vengono controllati per verificare la conformità PDF/X. Ciò avviene nel caso in cui un file master sia stato modificato e nel file sia stato introdotto un elemento o una caratteristica non PDF/X. A questo punto, alcuni problemi saranno corretti, ma altri, quali l'incorporamento di font, la sostituzione di immagini e la conversione dei colori, tuttavia non possono essere gestiti in questa fase e determinano l'interruzione dell'elaborazione del file. Il file deve essere nuovamente rifinito in PDF/X. È necessario eseguire la sostituzione di OPI? PDF/X-1a:2001 richiede che i file non contengano commenti OPI. Si prevede che la sostituzione OPI sia stata eseguita e che il destinatario del file PDF/X non richieda risorse esterne aggiuntive (caratteri o immagini) per elaborare il file. È possibile rifinire un file PDF/X-1a:2001? Sì. Prinergy gestisce un file PDF/X-1a:2001 come qualsiasi file di input PDF. Il file può essere modificato in un normale file PDF oppure può essere ulteriormente rifinito in un file PDF/X-1a:2001. Se viene rifinito in un file PDF normale, non dispone più delle chiavi di identificazione PDF/X-1a:2001. Se viene rifinito in PDF/X-1a:2001, Prinergy lo controlla come qualsiasi altro file di input che sia rifinito in PDF/X-1a:2001. E per quanto riguarda gli strumenti di controllo PDF/X? Kodak ha testato le seguenti funzioni di controllo PDF/X:
Durante i test effettuati, l'output di PDF/X-1a ha superato costantemente gli strumenti di controllo Apago e DDAP.
Ci sono problemi noti relativi all'implementazione di PDF/X-1a:2001 in Prinergy? Se una pagina PDF/X con la chiave Trapping impostata su true viene portata in Prinergy e rifinita con la sezione Trap del modello di processo attivata, Prinergy tenta di eseguire nuovamente il trapping della pagina. Cosa succede se non si desidera utilizzare la funzione PDF/X in Prinergy? Se non si desidera utilizzare il formato PDF/X come file master digitale, è sufficiente configurare il modello di processo in modo da generare un PDF anziché un PDF/X-1a:2001. Prinergy genera un file master digitali come di consueto. In questo modo è possibile utilizzare la funzionalità Prinergy che non è possibile con PDF/X. Informazioni sul formato PDF/X-3 Un file PDF/X-3 può contenere Tipi di output, che indicano il dispositivo di destinazione del file, incluso il suo profilo colore. Informazioni sul formato PDF/X-4 È possibile utilizzare Prinergy 8.4 per verificare i file di input PDF/X-4 tramite Preflight+. Dove posso trovare ulteriori informazioni sul formato PDF/X?
|